Maintaining A Chainsaw-Best Mini Chainsaw Cordless

Best Mini Chainsaw Cordless

Maintain the saw in accordance with the manufacturer’s recommendations, ensuring that all safety devices are in good working order and that all guards are in place. It will need to be serviced on a regular basis by someone who is qualified to do so.========>

To keep the saw in safe working condition, operators must be trained in proper chain-sharpening techniques as well as chain and guide bar maintenance. Operators must report any damage or excessive wear found during daily checks on the following items:


switch for turning on/off;

brake chain;

catcher of chains;


chain links, drive sprocket, and guide bar

front and rear hand guards, as well as a side plate;

mounts for anti-vibration;

starting cord to ensure proper tension



Employers are responsible for providing and utilizing personal protective equipment (PPE) at work. PPE is equipment that protects the user from health and safety hazards at work. Safety helmets, gloves, eye protection, high-visibility clothing, safety footwear, safety harnesses, and respiratory protective equipment are examples of such items.


PPE should only be used as a last resort, that is when all other methods of eliminating or reducing risk have been exhausted.


Risk reduction has been considered. When choosing PPE, ensure that it is CE marked and that it is appropriate for the user.


size, fit, and so on If more than one piece of PPE is worn at the same time, ensure that they can be used together; for example, wearing safety glasses may disturb the seal of a respirator, resulting in air leaks. Ensure that PPE users are instructed and trained on how to use it and that it is maintained and available at all times. Protective clothing that meets the relevant standard should provide a consistent level of resistance to chainsaw cut-through. Other clothing worn in conjunction with the PPE must be close fitting and non-snagging. It should be noted that no protective equipment can provide complete protection against cutting by a hand-held chainsaw.


PPE standards that apply:


EN 397 safety helmet Arborists working from a rope and harness are advised to wear a mountaineering helmet. Hearing protection in accordance with EN 352-1. Mesh visors to EN 1731 or safety glasses to EN 166 are recommended for eye protection. Chainsaw jackets conform to BS EN 381-11 for upper body protection.

Chainsaw jackets can provide additional protection in situations where operators are at higher risk (eg trainees, unavoidable use of a chainsaw above chest height). However, this must be balanced against the increased heat stress caused by physical exertion (eg working from a rope and harness).

Gloves: In most cases, the use of appropriate gloves is advised. The type of glove will be determined by an assessment of the task and machine’s risk. Consider the need for protection against chainsaw cuts, thorny material, and cold/wet conditions. Chainsaw gloves must meet EN 381-7 standards where they are required.


Leg protection according to EN 381-5. (Arborists working in trees and occasional users, such as those in agriculture, should wear all-around protection.) Chainsaw boots conforming to BS EN ISO 20345:2004 and bearing a chainsaw shield to demonstrate compliance with EN 381-3. (Protective gaiters conforming to EN 381-9 may be worn in conjunction with steel-toed safety boots by occasional users working on even ground where there is little risk of tripping or snagging on undergrowth or brash.)


Employees who work alone

Lone workers should not be put in a higher risk category than other employees. Before allowing people to work alone, consider and address any potential health and safety hazards. Take into account the following:

whether there is a need to assess risk areas such as violence, manual handling, the individual’s medical suitability to work alone, and any risks arising from the nature of the workplace itself;

whether there are any specific training requirements or levels of experience required;

What systems might be required to supervise and communicate with lone workers if a risk assessment indicates that this is necessary?

Working with a chainsaw alone is not recommended. If this is not possible, make plans to notify authorities if something goes wrong. These could include:

regular communication with others via radio or telephone;

someone who comes to the job site on a regular basis;

carrying a whistle to sound an alarm;

an automatic signaling device that, unless prevented, sends a signal at a predetermined time;

checks to ensure that operators return to base or home on time

You are responsible for ensuring that your employees receive immediate medical attention if they become ill or are injured at work. Your plans will be determined by the specific circumstances of your workplace, and you must assess your first-aid requirements. You must have at the very least:


a well-stocked first-aid kit;

a designated person in charge of first-aid arrangements;

All employees should be given information about first-aid arrangements.

You may decide that you require the services of a first-aider, which is someone who has been trained by an approved organization and holds a qualification in first aid at work or emergency first aid at work.

There is no legal requirement for operators to have an emergency first-aid certificate at work, but we recommend that they do. Anyone who works with chainsaws requires


to be trained in emergency first aid, particularly in controlling major bleeding and dealing with crush injuries People who have been injured in remote locations may also be at risk of hypothermia. Ensure that operators always carry a personal first aid kit (including a large wound dressing) and have reasonable access to a more comprehensive kit.


Chainsaw operation—fueling and lubrication

Make certain that gasoline containers are in good condition, clearly labeled, and have securely fitting caps.

Use containers designed specifically for chainsaw fueling and lubrication. Install an auto-filler spout on the outlet of a gasoline container to reduce the risk of spillage caused by overfilling. Operators must:


Avoid getting dirt in the fuel system (this can cause the chainsaw to break down).

Replace all filler caps securely immediately after fueling/oiling;

blot up any spilled gasoline or oil;

During starting and use, keep fuel containers away from fires and other sources of ignition, including the saw itself (at least 4 m is recommended).

Do not allow operators to use discarded engine oil as a chain lubricant; it is a poor lubricant and may cause cancer if it comes into contact with an operator’s skin on a regular basis. Starting the chainsaw and performing pre-use inspections Operators must check the following items before using a chainsaw:


All nuts, screws, and other fasteners are tight;

The saw chain has been properly tensioned.

The throttle cannot be pressed unless the throttle lock-out switch is depressed.

They are outfitted with the necessary personal protective equipment (PPE).

When starting the saw, keep a safe working distance from other people and make sure the saw chain is clear of any obstructions. Operators must do the following when starting a chainsaw with a cold engine:

place the saw on a level surface;

Put a foot on the rear-handle base plate and a hand on the front handle to firmly secure the saw.

configure the controls in accordance with the manufacturer’s recommendations;

Firmly pull the starter cord. After starting the saw, operators must rev the throttle to warm up the engine and ensure that:

When the engine revs return to idle, the saw chain stops moving.

When used at maximum revs or as specified by the manufacturer, the chain brake is effective.

When the saw is turned through 90° in any direction, the engine continues to run.

The stop button is operational;

The guide bar and chain are properly lubricated.

These checks must be carried out at regular intervals throughout the day. Operators can use the same method as described above to start a chainsaw with a hot engine. They can also grip the rear handle firmly between their knees and the front handle with their left hand while pulling the starter with their right. After starting the saw, operators should apply the chain brake before moving the saw. Hot starting is possible with most modern chainsaws when the chain brake is engaged.




The uncontrolled upward and backward movement of the chain and guide bar towards the operator is referred to as kickback. This can happen when the saw chain at the guide bar’s nose collides with an object.

Kickback is responsible for a significant portion of chainsaw injuries, many of which are to the face and upper body, where protection is difficult to provide. A properly maintained chain brake and the use of low-kickback chains (safety chains) reduce but do not completely eliminate the effect. Make certain that operators use the saw in a safe manner.


kickback from:


not allowing the guide bar’s nose to come into contact with any obstruction, such as branches, logs, or stumps;

not going too far;

keeping the saw below the level of your sternum;

keeping the left hand’s thumb around the back of the front handle;

utilizing the proper chain speed for the material being cut

Making use of the chainsaw


Whatever the job, thoroughly inspect the worksite to identify any potential hazards. This is especially important when performing felling or demolition work. Maintain a clear working area on the job site whenever possible. If you’re going to use a chainsaw, make sure you do the following:


The risks associated with the work have been assessed and managed;

The operator is qualified for the job;

The operator is outfitted with the necessary personal protective equipment (PPE).

When not cutting with the saw, the operator either turns off the engine or applies the chain brake.

Handling by hand


Over a third of all workplace injuries are caused by manual handling. Work-related musculoskeletal disorders (MSDs) such as upper and lower limb pain/disorders, as well as joint and repetitive strain injuries of various types, are examples. Manual handling encompasses a wide range of tasks such as lifting, lowering, pushing, pulling, and carrying. There is a risk of injury if any of these tasks are not completed properly.


Manual handling of injuries can have serious consequences for both the employer and the injured party. They can happen almost anywhere in the workplace, and heavy manual labor, awkward postures, and prior or current injury can all increase the risk. Avoid such tasks as much as possible in the workplace to help prevent manual handling injuries.

Where it is not possible to avoid handling a load, employers must consider the risks of that task and implement reasonable health and safety measures to prevent and avoid injury, including the use of lifting aids where necessary. These simple guidelines will assist operators:


Lift only when absolutely necessary;

only lift loads that are well within their capabilities;

Lift with your back straight, not bent, stretched, or twisted;

Keep loads close to the body at all times.

if they require assistance, they should seek it;

give themselves adequate rest breaks

Instruments of assistance


If you invest in a few simple pieces of equipment, such as pulp hooks, log tongs, and high lift wedges, operators will find it much easier to follow these rules. When used correctly, they will assist operators in completing tasks with minimal effort and a straight back. Proper body alignment It is critical that forces on the back are applied evenly, whether on the ground or up a tree.

Before lifting, operators should assume a position that provides secure footing while not forcing them into an awkward posture. To maintain balance, keep your feet apart and one leg slightly forward. If operators are levering over a tree, moving pieces of timber, or simply picking up a chainsaw, they should do so with bent knees, a straight back, and the load as close to the body as possible.


As a result, they are lifting with their strong leg muscles rather than their backs. Operators should not lever over a tree while pushing on the tree with one hand and pulling on the lever with the other. The back will be stretched and twisted, with the lower back muscles bearing the majority of the load.

When lifting, it is critical that operators have a good grip and are free to adjust their position for the best lift. Using properly sharpened pulp hooks or log tongs is one of the best methods. This will also help to preserve their gloves and reduce the amount of bending they have to do. They should use both hands, or else they will twist their back. In some cases, a log pick can be a useful handling tool.


Making use of a mini cordless chainsaw


Operators may not consider their chainsaw to be a load, but it is! The strain on their back will be significant if they work in a stooped position with the weight of the saw hanging from their arms.

When making a felling cut on a tree, operators can support the weight of the saw by bracing their forearms against their thighs or knees. When crosscutting and debranching, resting the saw on the thigh relieves strain on the lower back muscles.

Operators should stay close to the saw to reduce the risk of kickback. They should strive to work at a height that allows them to easily support the saw on the tree without stooping.


Timber handling

Operators should cut the timber into manageable pieces and enlist the assistance of others for the larger sections. They can frequently avoid lifting by rolling, pivoting, or sliding the wood. The more planning that goes into felling and processing the trees, the easier this will be. Aid tools will assist operators in performing their duties safely. If they must transport timber, they must ensure that the ground is clear of obstacles and tripping hazards.


hefty weights


When it comes to heavy loads, even good lifting techniques have limitations. Operators should use equipment that gives their bodies a significant advantage whenever possible. When feeling large or awkward trees, a portable winch is useful for applying large forces. It will also make turning over a large tree stem easier. Likewise high


Lift wedges allow operators to apply forces far greater than those of a breaking bar; their use saves operators’ backs and gives them far more control. Felling cushions, which can be used in place of wedges, are also available. The chainsaw’s exhaust gas is used to inflate the cushion and knock the tree over. Allow a machine to handle some tasks.


Correct manual handling is an essential part of the job. Recognized training courses for chainsaw work and some other tasks involving timber handling are available. These will teach operators how to complete their tasks safely and efficiently without putting their backs out. Before any felling begins on the Jobsite:


Contact the owners of any overhead power lines within twice the height of any tree to be felled to determine whether the lines need to be lowered or made dead.

Do not begin work until you have agreed on the precautions to be taken.

Check to see if there are any underground services, such as power cables or gas lines, that could be damaged if the tree falls.

If there are roads or public rights of way within twice the height of the tree to be felled, make sure that no road users or members of the public enter the danger zone. You may need to plan for warning signs, detours, or traffic control.

When felling a tree, remember to:

Check to see if it has rotted.

Examine factors that may influence the fall direction, such as wind conditions and whether the tree is leaning, has uneven growth, or branches that may foul other trees.

Check for broken crowns and branches that may fall during the operation with special care.

Examine both the tree to be felled and the trees nearby;

Operators may require the use of assistance tools such as alloy or plastic wedges, a breaking bar, a can’t hook, a winch, or high-lift wedges and a sledgehammer.

Ensure that operators have the appropriate equipment and the skills to use it correctly.

If a tree becomes entangled or is likely to become entangled on another during felling, operators must have the knowledge and equipment to safely bring it down. Managing leaning trees or wind-blown trees also require special skills

Tips on How to Buy a Chainsaw

Many people use shears to remove and prune overgrown plants and shrubs in the garden. However, there are times when gardening tools are insufficient, and the only option is to use a chainsaw. Those in desperate need of a chainsaw should be aware that it is one of the most dangerous and powerful gardening tools available on the market. As a result, it is critical to select the proper type of chainsaw for gardening.

When it comes to cutting an overgrown tree or even a whole tree, remember that an excellent chainsaw is the best tool for the job. However, before you go out and buy a chainsaw, there are a few things you should know about the various types on the market. These chainsaws have their own jobs, and certain tips have proven to be useful for buyers like you in selecting the best tool to meet your gardening needs.

Selecting the Righ Chainsaw

Furthermore, selecting the best chainsaw is critical because the wrong one may not be adequate for the job. Furthermore, even handling it while cutting grass or trees can be hazardous. Any homeowner looking for the best chainsaw should use the tips as a guide when selecting a chainsaw.

Different Types of Chainsaws

Knowing the various types of chainsaws is one of the most important considerations. There are many of these types on the market, including gasoline and electric chainsaws. They both have their own set of flaws and strengths. As a result, it is necessary to consider and even compare their characteristics.

Electric Chainsaw

Actually, an electric chainsaw is lightweight, inexpensive, and quiet, making it ideal for small jobs. However, it requires an electrical outlet and is not as strong and powerful as a gasoline-powered chain saw. A petrol-powered chain saw, on the other hand, is more powerful and ideal for frequent jobs, as it does not require an electrical cord. Because of these benefits, it retains its high price, despite being heavy, bulky, and noisy. Buyers will undoubtedly require electric chainsaws for light work, whereas petrol-powered chainsaws are ideal for long distances.

Choosing a Bar Length

The second tip is to select the appropriate chainsaw bar length for the job. Before purchasing a chainsaw, it is critical to consider the type of job. In general, the longer the bar length required, the larger the wood to be cut. The bar length ranges from ten to more than twenty inches, or from twenty-five to more than fifty-one centimeters.

Best Chainsaw Fit For You

The third tip is to select a chainsaw with the proper fit, which means it can be carried and held comfortably. This allows users to work much more efficiently than if they had to consider the available space and handle size between the rear and front handles.

Safety Features

The fourth and most important tip is to double-check the main safety features. Modern chain saws already have important safety and design features. Chain brakes, vibration-dampers, and kickback protection are among the safety features.


The final important tip is to consider the ease and convenience of controlling the chainsaw, as well as its dependability. When purchasing a chainsaw, it is critical to ensure that the tool is simple to use. It is preferable to hold them first before purchasing to ensure that the weight and size are correct. Whereas there are many popular brands of chainsaws to buy on the market, dependability is also required.


You now have a better understanding of the factors to consider when purchasing a chainsaw!